#1 AUTO PARTS DEMOLITION DERBY
Wednesday, August 10, 2016 — 7:00 p.m. Thursday, August 11, 2016 — 7:00 p.m.
New Revised entry blank with improved rules. Large cars, small cars, Mini Vans and pickups both nights.
www.woodbooger-demolition-derby.com — 508-577-6850, DIRECTOR: Diane Norris, 897-7014
RULE BOOK DISCLAIMER. The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These rules shall govern the condition of all events, and by participating in these events, all participants are deemed to have complied with these rules. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM PUBLICATIONS OF OR COMPLIANCE WITH THESE RULES AND OR REGULATIONS. They are intended as a guide for the conduct of the sport and are in no way a guarantee against injury or death to a participant, spectator, or official.
The race director shall be empowered to permit reasonable and appropriate deviation from any of the specifications herein or impose any further restrictions that in his/her opinion does not alter the minimum acceptable requirements. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM SUCH ALTERATION OF SPECIFICATIONS. Any interpretation or deviation of these rules is left to the discretion of the officials. Their decision is final. The Management of Woodbooger Demolition Derby
1. You must have a full face helmet, DOT approved.
2. You must have a working seatbelt.
3. You must wear long pants, no shorts.
4. Driver door must be painted FLOURESCENT GREEN.
5. Each vehicle must have a fire extinguisher located in the padding of the front passenger seat.
1. You must make contact every 60 seconds. You must give not receive.
2. Do not hit the drivers’ door. If you see green do not hit it.
3. Excessive smoking will be disqualified.
4. Sandbaggers will be disqualified.
5. Red Flag means stop, there may be a fire. Pay attention.
6. The last car to make a hit will be deemed the winner. Officials’ decision is final.
1. Any passenger car, No Imperials, pre 1970 Lincolns, Hearse or Limousines. Pre-derbied cars are acceptable as long as they are not re-enforced or welded. EXCEPTION **BROCKTON FAIR MUST BE 1980’s OR NEWER VEHICLE**
2. Absolutely no welding is allowed anywhere on your car, unless otherwise noted below, no matter how small. You will be sent home..
3. You must have a roof sign with your number painted on it. Any number or word (nothing offensive) is allowed.
4. Remove all glass including the windshield. Doors must be clean and free of glass.
5. Remove all bumper covers, lights and molding or anything that can be knocked loose onto the track.
6. Engines, transmissions and rear ends must be the same make as the car, unless otherwise noted.
7. Fuel tank may be moved inside of the car, forward of the rear wheels and behind the front seat. Fuel tank must be marine type plastic or metal, six (6) gallon maximum. Fuel tank must be secure and deemed safe by the inspectors. You must cover the fuel tank. If tank is left in original position it should have a shield and no more than six (6) gallons of gas. EXCEPTION **CROWN VICS, GRAND MARQUIS AND LINCOLNS MUST HAVE
TANK MOVED INSIDE THE VEHICLE**
8. One battery only. Battery may be moved to passenger side front floor and must be covered with a rubber mat. If battery is left in place, spray foam cannot exceed 6 inches from battery.
9. All anti-freeze must be removed, water only in radiator.
10. Rear differential may be locked or welded for posi-traction. Rear end may be from a different manufacturer as long as it bolts directly in, has not been modified in any way and trailing arms must remain original to the vehicle. (EX. GM rear end bolts in directly to Ford)
11. Drivers’ door (only) may be welded with a maximum 12 inches on each seam (fender, backside and bottom). You may install 2 pipes in an “X” or one pipe straight across, maximum 3 inch pipe or tube behind the driver seat from door to floor for safety reasons only. Maximum 6 inch square plates at each end, this may be welded in. If you do not have a passenger seat a bar is mandatory.
12. Remaining doors must be open for inspection and may be chained or wired shut after inspection.
13. Hood and trunk may be chained or wired shut in four places only after inspection. Wire must be #9 gauge maximum, two (2) strands per hole. Hood and trunk may be wired or chained around through bumpers in two (2) of these holes.
14. Motor mounts and transmission mounts may be wired, chained or welded.
15. Any air filled tires, 1/4” thick weld in universal wheel centers are permitted. This is for lug pattern purposes only. No larger diameter center will be allowed.
16. No cutting of bumpers. NO CUTTING OF BUMPERS. No aftermarket bumper mounting brackets. Any bumper may be used as long as it is not modified. You may weld front bumpers ONLY with 4, 1 inch maximum welds on each shock or mounting side. You may not add any steel.
17. Fender wells may be cut for clearance; however, they may not be welded, rolled or re-attached for strength.
18. Shifting linkage may be hooked up direct to the transmission. Shifter handle must be safe.
19. All transmission lines must be disconnected from the radiator to prevent oil spills. A transmission cooler may be installed under the hood or the lines must be looped.
20. Electrical system hot wires may be installed.
21. Air cleaner must be in place.
22. There must be must be (2) 6” X 6” openings in the hood. One on either side for fire department access. Hood holes may be cut out, no folding, rolling or reinforcing around hood openings.
23. Exhaust may be exited through the hood.
24. All body mounts must be original and cannot be repaired or altered in any way. If it looks like it has been tampered with the body bolt will be removed and replaced with two strands of #9 wire. Officials discretion.
25. The rear of the car may be bent up a maximum of 2 inches. There is no hammering, kinking or folding any part of the car such as quarter panels or roof posts. It will be the official’s decision to if you have overdone it and you will be made to bend it back to original.
26. If your car has anything on it that did not come from the factory (distributor protectors, engine cradles, pulley protectors, rear end braces, etc) it must be removed unless noted in rules.
27. Suspension must be stock, no added leaf springs or heavier than stock to that vehicle coil springs. You may use one piece of chain no larger than 5/16” Diameter at each wheel area to set desired height.